Brand HP tank / HPA bottle with pre-regulator 0.8L (48ci) - 200 bar / 3000 PSI
This HPA bottle is made of aluminum with a stainless steel core, which makes it lighter than normal steel bottles.
There is a 1/8 MTP thread at the top of the bottle regulator onto which the "gun regulator" can then be screwed.
Procedure for the correct assembly sequence:
First screw on the gun regulator, then connect the hose, then connect the hose to the gun and only then turn on the pressure.
Please note / safety instructions:
Never set the pressure above the maximum specifications of the gun (i.e. the maximum pressure of the HPA system installed in the gun), as this can lead to irreversible defects in the system. The cylinder is equipped with two pressure relief valves (bursting discs 1.8K and 5K), which burst when overfilled.
Technical data:
Length of the cylinder : 295mm
Diameter of the cylinder : 90mm
Weight of the cylinder : 1345g
Filling pressure : 3000 PSI
Service life and handling of HPA cylinders:
HPA bottles have a fixed defined service life of 10 years. All bottles are valid for 10 years from the date of production, after which they must be replaced. The date of manufacture of aluminum bottles is usually stamped on the neck of the bottle. It is important to handle your bottle with care. Avoid drops, transport safely in separate containers and do not fill too quickly as this can cause damage. Handling HPA Bottles requires a sense of responsibility as they are under high pressure. Always pay attention to their condition to avoid serious accidents.
The item shown above is a tested accessory for HPA systems. Barrels have been used for a long time during development and tested for function
Further interesting articles and information about HPA systems
- Begadi "TAIFUN" HPA/CO2 Regulators
- Begadi "HURRICANE" HPA/CO2 Regulators
- Begadi HPA "Flex" hose, 100cm -black
- Begadi HPA "Flex" hose, 100cm - od-green
- Begadi HPA "Flex" hose, 100cm -TAN / FDE-
- Begadi Adjustable Pouch for HPA, 425g CO2 and gas cylinders -olive
- Begadi Adjustable Pouch for HPA, 425g CO2 and gas cylinders -flecktarn
There is a 1/8 MTP thread at the top of the bottle regulator onto which the "gun regulator" can then be screwed.
Procedure for the correct assembly sequence:
First screw on the gun regulator, then connect the hose, then connect the hose to the gun and only then turn on the pressure.
Please note / safety instructions:
Never set the pressure above the maximum specifications of the gun (i.e. the maximum pressure of the HPA system installed in the gun), as this can lead to irreversible defects in the system. The cylinder is equipped with two pressure relief valves (bursting discs 1.8K and 5K), which burst when overfilled.
Technical data:
Length of the cylinder : 295mm
Diameter of the cylinder : 90mm
Weight of the cylinder : 1345g
Filling pressure : 3000 PSI
Service life and handling of HPA cylinders:
HPA bottles have a fixed defined service life of 10 years. All bottles are valid for 10 years from the date of production, after which they must be replaced. The date of manufacture of aluminum bottles is usually stamped on the neck of the bottle. It is important to handle your bottle with care. Avoid drops, transport safely in separate containers and do not fill too quickly as this can cause damage. Handling HPA Bottles requires a sense of responsibility as they are under high pressure. Always pay attention to their condition to avoid serious accidents.
The item shown above is a tested accessory for HPA systems. Barrels have been used for a long time during development and tested for function
Further interesting articles and information about HPA systems
- Begadi "TAIFUN" HPA/CO2 Regulators
- Begadi "HURRICANE" HPA/CO2 Regulators
- Begadi HPA "Flex" hose, 100cm -black
- Begadi HPA "Flex" hose, 100cm - od-green
- Begadi HPA "Flex" hose, 100cm -TAN / FDE-
- Begadi Adjustable Pouch for HPA, 425g CO2 and gas cylinders -olive
- Begadi Adjustable Pouch for HPA, 425g CO2 and gas cylinders -flecktarn
Review Partner