Maxx Model M4 / M16 CNC Alu HopUp Unit M4A PRO -rot-
![EPeS O-ring set for (S)AEG HopUp units, pack of 4 [E044-HK]](https://www.begadi.com/media/catalog/product/cache/a491986f8011072f66fb1fed37f51dcc/b/-/b-epes-e044-hk-oring-set-for-aeg-hopup-chambers-g.jpg)
This HopUp Chamber fits M4/M16 AEG models with common V2 Gearbox.
For ICS Maxx Model offers a separate unit (M4I), which can be found in the store under item number 18522020.
Please see below the installation instructions + info about the compatibilities
What is new with the M4A and M4I?
The "Side Wings" can be removed, this is important for Outer Barrels which do not comply with the standard.
Also the available tensioners have been revised and offer more possibilities than the predecessor.
Features:
- CNC machined from one block of 6061 aluminum
- BB Latching System prevents BBs from falling out of the Feeding Tube when changing magazines
- Built-in adjustment dial for precise, infinite adjustment
- Nozzles from 21.00 - 21.25mm can be used
- Compatible with most third party HopUp rubbers
- 2 clear vinyl plates are attached to the side, allowing a clear view over the remaining BBs in the HopUp Chamber
- Included with delivery are 3 tensioners. (only for 5mm systems)
BB Latching System:
Please note that this system is not compatible with all magazines and different manufacturers. Begadi can unfortunately not give any warranty for the different systems.
LED Tracer Board:
The M4A and M4i are no longer compatible with the LED Tracer Board V2.
Dimensions:
Length: 51mm
Height: 37,75mm
Outerbarrel diameter: min. 12mm
Nozzle diameter: max. 7,8mm
Feeding Tube diameter: 8,9mm
Feeding Tube Length: 6mm
Installation Notes:
The following things should be considered when installing the Hop Up Unit:
It may be necessary to change the Nozzle. MAXX specifically recommends a Nozzle length of 21.00mm to a maximum of 21.25mm in its installation instructions.
Standard M4 Nozzles usually have a length between 21.2mm - 21.4mm which can lead to feeding problems when using this Hop Up Unit.
Basically we recommend to order directly a suitable Nozzle.
Notes on Compatibilities:
Not compatible with Begadi Sport/Cyma models (adjustment wheel too big, Nozzle not compatible)
Scope of delivery:
- HopUp Unit
- Adjusting wheel (installed)
- Inlet (11mm, installed)
- C-Clip
- Tensioner for 5mm systems (flat, rubber)
- Tensioner for 5mm systems (rounded, aluminum)
- Tensioner for 5mm systems (3mm round, rubber)
- Spring
- Spring for Outer Barrel (installed)
- Brass ring
- O-Ring for Inner Barrel
Links & Downloads:
-Maxx Model M4 / M16 CNC Alu HopUp Unit M4A PRO -red-, Manual sheet 1
-Maxx Model M4 / M16 CNC Alu HopUp Unit M4A PRO -red-, Manual sheet 2
-Delrin C-Clip for Maxx Model HopUp Units
Comparison pictures M4A PRO + M4I PRO:
Comparison pictures to the model predecessor ME PRO:
For ICS Maxx Model offers a separate unit (M4I), which can be found in the store under item number 18522020.
Please see below the installation instructions + info about the compatibilities
What is new with the M4A and M4I?
The "Side Wings" can be removed, this is important for Outer Barrels which do not comply with the standard.
Also the available tensioners have been revised and offer more possibilities than the predecessor.
Features:
- CNC machined from one block of 6061 aluminum
- BB Latching System prevents BBs from falling out of the Feeding Tube when changing magazines
- Built-in adjustment dial for precise, infinite adjustment
- Nozzles from 21.00 - 21.25mm can be used
- Compatible with most third party HopUp rubbers
- 2 clear vinyl plates are attached to the side, allowing a clear view over the remaining BBs in the HopUp Chamber
- Included with delivery are 3 tensioners. (only for 5mm systems)
BB Latching System:
Please note that this system is not compatible with all magazines and different manufacturers. Begadi can unfortunately not give any warranty for the different systems.
LED Tracer Board:
The M4A and M4i are no longer compatible with the LED Tracer Board V2.
Dimensions:
Length: 51mm
Height: 37,75mm
Outerbarrel diameter: min. 12mm
Nozzle diameter: max. 7,8mm
Feeding Tube diameter: 8,9mm
Feeding Tube Length: 6mm
Installation Notes:
The following things should be considered when installing the Hop Up Unit:
It may be necessary to change the Nozzle. MAXX specifically recommends a Nozzle length of 21.00mm to a maximum of 21.25mm in its installation instructions.
Standard M4 Nozzles usually have a length between 21.2mm - 21.4mm which can lead to feeding problems when using this Hop Up Unit.
Basically we recommend to order directly a suitable Nozzle.
Notes on Compatibilities:
Not compatible with Begadi Sport/Cyma models (adjustment wheel too big, Nozzle not compatible)
Scope of delivery:
- HopUp Unit
- Adjusting wheel (installed)
- Inlet (11mm, installed)
- C-Clip
- Tensioner for 5mm systems (flat, rubber)
- Tensioner for 5mm systems (rounded, aluminum)
- Tensioner for 5mm systems (3mm round, rubber)
- Spring
- Spring for Outer Barrel (installed)
- Brass ring
- O-Ring for Inner Barrel
Links & Downloads:
-Maxx Model M4 / M16 CNC Alu HopUp Unit M4A PRO -red-, Manual sheet 1
-Maxx Model M4 / M16 CNC Alu HopUp Unit M4A PRO -red-, Manual sheet 2
-Delrin C-Clip for Maxx Model HopUp Units
Comparison pictures M4A PRO + M4I PRO:
Comparison pictures to the model predecessor ME PRO:
Review Partner